GASKET SHEET : ปะเก็นแผ่นทนความร้อน
ปะเก็นแผ่น คือ วัสดุที่มีลักษณะเป็นแผ่น ใช้ประกอบในชิ้นส่วนเพื่อกั้นระหว่างหน้าสัมผัสผิววัสดุทั้ง 2 ชิ้น นำมาประกบติดกัน เพื่อป้องกันการรั่วไหลของของเหลว หรือบางครั้งป้องกันการรั่วไหลของอากาศ ที่บรรจุอยู่ภายในซึ่งมกพบเห็นในการใช้งานเกี่ยวกับ ฝาสูบ หน้าแปลน แม่พิมพ์ หรือชุดเฟือง ปะเก็นแผ่นจะแบ่งตามวัสดุ คุณสมบัติการใช้งานที่ต่างกันออกไป เหล่านี้เรียกว่า "ปะเก็นทนความร้อน" อาทิเช่น ปะเก็นกราไฟรท์ (Graphite sheet), แอสเบสตอส (Asbestos sheet), นอนแอสเบสตอส (Non Asbestos sheet) ฯลฯ เรายังนำแผ่นเหล่านี้มาขึ้นรูปตามมาตรฐานหน้าแปลน แม่พิมพ์ และฝาสูบได้อีกด้วย
GRAPHITE SHEET
SERIES : KN5201/A/B/C/D
Material :
Graphite is a compressible and high thermally conductive material that has been used primarily to make sealing gaskets because of its ability to conform to rough surfaces, withstand high temperatures, and resist corrosive fluids.
Graphite is a compressible and high thermally conductive material that has been used primarily to make sealing gaskets because of its ability to conform to rough surfaces, withstand high temperatures, and resist corrosive fluids.
SERIES : FEROLITE 333
ASBESTOS SHEET
Material Composition : Made from Chrysotile Asbestos Fiber with Synthetic & Natural Elastomers and Inorganic fillers.
Application : To Seal off steam, Air, Water, various alkaline chemicals under low stress conditions. Surface finish : Red, Grey, Graphited Operating Condition Maximum pressure : 35 K.g/cm2 Maximum temperature : 380°C Specification compliance : IS : 2712 / 1998 GRADE W/3 |
SERIES : FEROLITE IT300
|
Material Composition : Made from Chrysotile Asbestos fiber with synthetic Elastomers and Inorganic fillers.
Application : Suitable for high stress conditions of water, steam, gas, alkalies, ammonia and other no aggressive media etc. Surface finish : Red, Grey, Graphited. Operating Condition Maximum pressure : 150 Kg/cm2 Maximum temperature : 550 °C Specification compliance : IS : 2712 / 1998 GRADE W/1, DIN : 3754 ASTM : F104 112001M7 BS : 2815-1973 GRADE A |
SERIES : FEROLITE SPECIAL
|
Material Composition : Made from Chrysotile Asbestos fiber with synthetic Elastomers and Inorganic fillers.
Application : Suitable to seal of steam, Hot oils & various aromatic Hydrocarbons solvents & Refrigerants in high stress condition. Surface finish : Green/Green Operating Condition Maximum pressure : 150 Kg/cm2 Maximum temperature : 550 °C Specification compliance : IS : 2712 / 1998 GRADE O1, BS : 1832-1991 GRADE O,BS : 1832/1973 GRADE A |
SERIES : FEROLITE NAM30Y
|
Material Composition : Aramid fiber, mineral fiber & inorganic fillers
Binders : Synthetic NBR Elastomers Operating Condition Max.Peak Temp : 400 °C Max.Continuous Temp : 250 °C (with steam220 °C) Max. operating pressure : 100 Kg/cm2 Specification compliance : BS 7531 GRADE Y |
Contact |
|
Line ID |